How are Microchips Made? 🖥️🛠️ CPU Manufacturing Process Steps
Branch Education
0:00 Inside this smartphone are 62 microchips
0:03 containing a total of 90 billion transistors.
0:07 These microchips are incredibly powerful and the cornerstone of all technology,
0:12 but how are billions of nanoscopic transistors manufactured
0:16 into a microchip the size of a tiny ant?
0:20 Well, all these microchips were manufactured
0:23 in a semiconductor fabrication plant like this one.
0:27 Inside it is a clean room which spans the area
0:31 of 8 football fields and is filled with hundreds of machines ranging
0:35 in size from that of a van to that of a city
0:39 bus and costing anywhere between a few million and 170 million dollars.
0:46 Within this microchip factory,
0:48 silicon wafers travel from machine to machine and undergo
0:53 around a thousand processes over a 3-month period.
0:57 And, by the end of production, each silicon wafer will be covered in hundreds
1:03 of CPU chips each containing 26 billion transistors.
1:06 When we zoom in we can see the nanoscopic transistors
1:11 at the bottom and over a dozen layers of wires above.
1:16 This integrated circuit is then cut out from the wafer, tested,
1:20 and packaged so that it can be installed into your desktop computer.
1:25 In this video we’re going to explore the entire microchip
1:29 manufacturing process and show you how billions of nanoscopic transistors
1:34 and an impossibly complex 3D maze of wires are manufactured
1:39 in one of the world’s most technologically advanced microchip factories.
1:45 It’s an incredibly complicated process, so stick around and let’s jump right in!
1:55 A portion of this video is sponsored by Brilliant.org.
2:03 There are two sides to understanding how microchip manufacturing works.
2:08 The first is the sequence of steps and processes needed
2:12 to build the nanoscopic transistors and the labyrinth of wires.
2:17 Whereas the second is how the semiconductor fab
2:20 and multimillion dollar equipment on the cleanroom floor work,
2:25 and we’ll be flipping between these two sides to get a complete picture.
2:31 Let’s start by opening up this desktop computer,
2:33 focusing on the CPU and taking a look at what’s inside.
2:38 Here we have an integrated circuit, or die, which we’ll refer to as a chip.
2:44 This chip has 24 cores, a memory controller,
2:48 a graphics processor, and many other sections.
2:51 Within one of the cores, we can see its block diagram and the various elements.
2:56 Zooming in on this multiply block, we find a layout of 44 thousand transistors
3:03 that physically execute 32-bit multiplication and constitute just
3:07 point zero zero zero one seven percent
3:11 of the overall 26 billion transistors in the CPU.
3:16 Zooming in even further, we see layers of metal wires, or interconnects,
3:22 and at the very bottom are the transistors that form the basic logic gates.
3:27 Note that these layers of metal interconnects aren’t floating, but rather,
3:32 the empty space that you see is filled with insulating materials,
3:37 thus providing structure, and preventing the metal wire layers from touching.
3:42 Furthermore, here we’re only showing the transistors at the bottom and five
3:47 layers of metal interconnects with vias traveling vertically between the layers.
3:52 In actuality there are a total of 17 metal layers of wires in the CPU,
3:58 and each successive set of levels uses larger and larger interconnects.
4:03 At the bottom are local interconnects that move
4:06 data around this 32 bit multiply circuit.
4:09 In the middle are intermediate interconnects that move data around the core,
4:14 and at the top are global interconnects that move data around the entire CPU.
4:20 You might be wondering how small are these transistors?
4:24 Zooming in again and past the interconnect layers we find FinFets,
4:30 which are transistors whose channel dimensions are 36 by 6
4:35 by 52 nanometers with a transistor to transistor pitch of 57 nanometers.
4:42 Clearly the transistors are incredibly small.
4:45 Here’s a mitochondria, a dust particle, and a human hair for size comparisons.
4:52 Now that you have a sense of what
4:55 the transistors and labyrinth of metal interconnects look like,
4:59 let’s explore how they’re manufactured.
5:01 We’ll begin with an analogy.
5:04 Imagine baking a cake that’s 80 layers tall,
5:08 with each layer cut to a unique shape.
5:11 To make this cake there are 940 steps in the recipe,
5:16 which takes 3 months to complete and includes hundreds of exotic ingredients.
5:21 And, if any measurement, baking time,
5:24 or temperature is more than one percent off, then the cake is entirely ruined.
5:30 That’s kind of what it’s like to make a microchip,
5:34 but microchips are even more complicated.
5:37 Let’s look at a single layer of this integrated circuit
5:41 and run through a simplified set of steps used to build it.
5:46 To start, a layer of insulating silicon dioxide is deposited on top of the wafer
5:52 and then a layer of light sensitive photoresist is spread across the top.
5:58 Next, using UV Light and a stencil, a pattern is applied to the photoresist.
6:05 Solvents then are used to remove the areas hit by the UV light,
6:10 thus creating a patterned mask layer.
6:13 Using the mask, the revealed silicon dioxide
6:17 is etched away down to the previous layer.
6:21 Next the mask layer is removed,
6:23 and a layer of copper is added to cover the wafer
6:28 and fill in the areas that were just etched away.
6:32 Finally, the surface is ground down and leveled
6:35 off to reveal the copper and insulator patterns.
6:39 And thus, a single layer is completed.
6:43 In order to build the next layer, which is a vertical set of metal vias,
6:48 we repeat the same set of steps, but use a different pattern for the photomask.
6:54 Since these layers are all built using the same set of steps
6:59 it’s more effective to visualize the steps as a circle like a clock.
7:04 To build all the 80 layers of the die,
7:08 this sequence is repeated over and over, resulting in 940 steps.
7:13 One important note is that the FinFet transistors
7:18 at the bottom are even more complicated than the metal wires,
7:23 and thus additional steps are needed to fabricate them.
7:26 Furthermore, cleaning the wafer to wash away dust
7:30 particles that may have landed on the wafer,
7:33 as well as inspecting the wafer to make sure everything is being built properly,
7:38 happens frequently and these steps need to be added to the circle.
7:43 A different tool is used to complete each of these process steps.
7:48 Now that we have an understanding of the steps,
7:52 let’s take a look at this semiconductor fabrication plant.
7:56 This CPU is manufactured on a 300-millimeter
7:59 silicon wafer which can fit 230 CPU chips.
8:04 In contrast DRAM chips are considerably smaller and thus
8:09 952 of them can fit on a wafer.
8:13 These silicon wafers are carried in stacks of 25 using
8:18 a container called a front opening universal pod, or foup.
8:23 This sealed plastic wafer carrier is
8:26 transported around the cleanroom floor using
8:29 an overhead transport system which lowers the foup onto the tool’s landing pad.
8:35 Inside the tool, robotic arms transport the wafer through vacuum
8:40 load locks and to different process chambers where materials are added,
8:45 removed, or processed in ways that we’ll explore later.
8:48 The wafers are then returned to the foup,
8:52 resealed inside, lifted up to the overhead transport system,
8:56 and carried to and dropped onto the next tool,
8:59 where the next step in the process is completed.
9:03 To build the entire chip composed of 80
9:06 different layers it takes 3 months of traveling
9:09 from tool to tool where at each stop one of the 940 process steps is completed.
9:15 In order to increase the microchip mass production
9:19 capabilities of a semiconductor fabrication plant or fab,
9:22 typically there are dozens of the same semiconductor
9:26 tools organized in rows that perform the same process.
9:31 On the cleanroom floor there are a total of 435 semiconductor tools resulting
9:37 in the fab’s production capacity of 50,000 wafers or 11.5 million CPUs a month.
9:45 These tools have rather complicated names,
9:49 so we’ll start by categorizing them according to their functionality.
9:53 There are 6 groups: making the mask layer, adding material, removing material,
10:00 modifying the material, cleaning the wafer, and finally inspecting the wafer.
10:05 We’ve color coded the different functional groups to the various
10:10 tools and process steps to help you not get lost.
10:15 Let’s next look at each of these semiconductor tools
10:18 and see how they process the wafer in various ways.
10:22 We’ll start with the ones that are used to make
10:25 the mask layer or the nanoscopic stencil on the wafer.
10:29 These tools include the photoresist spin coater,
10:33 photolithography tool, developer and photoresist stripper.
10:37 First the photoresist spin coater applies a light-sensitive layer
10:42 to the surface of the wafer and sends it
10:45 through a soft bake where the wafer is heated
10:47 in order to evaporate the solvent from the photoresist.
10:51 Next the wafer goes to the lithography
10:54 tool which shines UV light through a stencil,
10:58 which is technically called a photomask.
11:00 The light passes through the stencil and is then demagnified
11:05 or shrunk down to produce a nanoscopic pattern on the wafer.
11:09 Wherever the light from the stencil touches the wafer,
11:12 the photoresist is weakened.
11:14 The wafer then goes to the developer
11:17 and the weakened photoresist is washed away,
11:20 leaving only the patterned nanoscopic stencil on the wafer.
11:23 The wafer is then sent through a hard bake to harden the remaining photoresist.
11:29 Next the wafer travels to other tools to undergo processing,
11:34 and once these processes are completed the wafer goes to a photoresist
11:40 stripper which uses solvents to dissolve and remove the photoresist mask layer.
11:45 And that’s how a mask layer is formed and then removed.
11:50 The photolithography tool is one of the most important,
11:53 so let’s take a look at it.
11:56 Inside is a UV light source, a set of lenses to focus the light,
12:01 a photomask which contains the stencil,
12:04 or design of the layer to be patterned, and a wafer carrier.
12:09 The photomask is 6 by 6 inches, and, based on the dimensions of the CPU,
12:16 can fit 2 copies of a single layer of the CPU design.
12:20 The purpose of using a photomask with these crazy optics
12:24 is because it’s a reliable way to copy and paste
12:28 a design for billions of nanoscopic transistors and wires onto
12:34 230 identical CPUs on a single wafer in a few minutes.
12:40 After the light passes through the photomask,
12:43 the UV light goes to more lenses in order to shrink down the pattern
12:48 by a factor of 4 and print a single layer of the design onto the photoresist.
12:54 The wafer carrier steps from position to position,
12:58 printing the photomask image at each stop, until all 230 chips are patterned.
13:05 Let’s clarify one detail.
13:07 In our previous examples, we talked a lot about this CPU having 80 layers.
13:13 Specifically, what we were referring to is the number of photomasks and mask
13:18 layers used to create all the different layers of patterns on the wafer.
13:23 Therefore, one complete CPU chip uses 80 different photomasks,
13:29 each costing 300,000 dollars.
13:31 With only one mask layer being patterned at a time,
13:36 this CPU chip will undergo 80 separate visits to the lithography tool.
13:42 We could spend another hour talking about photolithography
13:45 but let’s move onto the next category of tools.
13:49 Deposition tools are used to add or deposit material onto the wafer.
13:54 A lot of times we use the mask layer from the photolithography
13:59 step to add materials to the areas uncovered by the mask layer,
14:03 kind of like spray painting through a stencil.
14:06 Due to the wide range of elements and compounds used to create the layers,
14:12 deposition tools have a wide range of variations
14:15 with complicated names and acronyms for each variant.
14:19 But essentially there are 3 key groups of materials
14:23 that are added or deposited onto the wafer: metals such as copper or tantalum,
14:30 insulators which are typically called oxides, and crystalline layers of silicon.
14:35 Each group of different materials uses different
14:38 physics and chemistry principles to deposit the material
14:41 on the wafer and therefore has a different
14:44 technical name for the tool that deposits the material.
14:48 Deposition tools typically have a central wafer handling chamber,
14:51 with the various chambers attached to the edges,
14:55 each one dedicated to adding just a single element or compound.
15:00 The next category of machines do the opposite, which is to remove material.
15:06 There are 2 key methods.
15:08 The first is etching.
15:10 Etchers use either corrosive chemicals or high energy plasmas to react
15:15 with and remove materials from the surface of the wafer.
15:19 They are typically used with the mask layer stencil
15:21 in order to remove the material exposed by the mask,
15:25 thus creating a hole that can be later filled by a deposition tool.
15:29 The second method to remove material is CMP,
15:34 which is chemical mechanical planarization.
15:37 CMP applies slurry and uses abrasive pads to grind
15:40 and polish away the top surface of the wafer, making it perfectly flat.
15:45 CMP levels off the top layers of the wafer
15:49 and is typically used as the last step
15:52 in a cycle of processes in order to prepare
15:55 the wafer for another layer to be added.
15:57 The fourth category are tools that modify
16:00 the silicon and are called ion implanters.
16:04 These tools use the photomask stencil
16:06 to bombard the unmasked regions with phosphor, boron,
16:11 or other elements in order to make the P
16:15 and the N regions required to form the transistors themselves.
16:19 Therefore, ion implanters are only used in the front end of line.
16:23 You might think that this is adding material.
16:26 However, ion implanters only add around one atom
16:30 of phosphor or boron for every 10,000 atoms of silicon.
16:34 Additionally, while other machines spray paint a layer on top of the wafer,
16:40 ion implanters hurl atoms deep into the silicon lattice,
16:43 kind of like a cannon launching a baseball 6 feet into a concrete wall.
16:49 This process typically damages the silicon lattice,
16:52 which is why the following step is to repair the silicon
16:56 by heating the wafer using a separate tool called an annealer.
17:00 The fifth category of tools are used to clean
17:04 and remove any contaminants or particles from the wafer.
17:07 These wafer washers use ultra-pure water to clean the wafer
17:11 and then dry it with nitrogen or hot isopropyl alcohol.
17:15 Cleaning the wafer happens rather frequently in order to remove
17:19 any stray particles that may have fallen onto the wafer.
17:24 And finally, sixth are tools that inspect the transistors
17:28 and metal layers for defects and are called metrology tools.
17:32 A common metrology tool uses a scanning electron microscope
17:36 with nanometer-level resolution to take pictures of the top surface
17:41 of the wafer and determine if there are defects
17:44 such as improperly patterned layers or particles on the surface.
17:48 When fabricating an integrated circuit that takes 3 months to complete,
17:52 it’s important to repeatedly monitor the progress and make sure
17:56 that each of the processes is being executed with nanometer-level precision.
18:02 Now that we’ve covered each of the categories,
18:06 here are the color coded process steps along
18:08 with the layout of the tools in the semiconductor fabrication plant.
18:12 Let’s run through the complete set of steps
18:15 used to manufacture a single metal interconnect layer.
18:19 First a layer of insulating silicon dioxide is deposited onto the wafer.
18:26 Next photoresist is spread across the surface and the wafer
18:30 is sent through a soft bake to remove the solvent.
18:34 The wafer then travels to the photolithography tool
18:37 where the design from the photomask is transferred
18:40 to each of the chips on the wafer
18:42 by weakening the areas of photoresist hit by the light.
18:45 The wafer next goes to the developer to wash away the sections that were hit
18:50 by the light from the lithography tool and then
18:53 through a hard bake to harden the remaining photoresist.
18:56 With the mask layer built, the wafer goes to an etching tool,
19:01 where a plasma etcher removes a vertical column through the exposed
19:06 silicon dioxide until it reaches the previous layer’s metal vias.
19:10 Next the wafer is sent to a photoresist
19:13 stripper where the mask layer is removed.
19:16 The wafer then travels to a physical vapor deposition tool where a sequence
19:22 of metals fills in the exposed pattern and coats the wafer in metal.
19:27 Finally the wafer is sent to a chemical mechanical planarization
19:31 tool where the metal is ground down so that all
19:35 that remains is a flat layer of insulating silicon dioxide
19:40 and conductive copper interconnects that match the pattern from the photomask.
19:45 A single metal layer is now completed,
19:48 and the wafer is ready for the next cycle to begin
19:52 where insulating silicon dioxide and the vias will be added.
19:57 Note that cleaning and wafer metrology or inspection
20:00 steps occur in between many of these other steps.
20:04 Furthermore, the process steps to make the transistors
20:08 are less straightforward and utilize the ion implanter,
20:11 and thus we’ll cover them in a separate video on transistor physics and design.
20:16 These steps are for building the integrated circuit on the wafer, however,
20:21 there are additional steps in manufacturing a microchip
20:24 which we’ll explore in a little bit.
20:26 But before we get there, one important thing to note is
20:31 that the semiconductor industry is incredibly secretive regarding
20:34 the exact tool layout and the process
20:37 steps and recipes used to make the transistors.
20:41 We wanted to make the best video on how microchips are made and it took us 180
20:47 hours of scouring the internet and textbooks for information
20:52 and reference images and, using what we found,
20:56 we spent 205 hours modeling each of these tools,
21:01 the many layers of the integrated circuit, and the semiconductor fab.
21:06 Furthermore, writing the script took about 100 hours,
21:11 and then animating all these visuals took more than 825 hours.
21:17 As a result, this video took over 1300 hours to make,
21:23 and it’s entirely free to watch.
21:25 We want to make more videos like this one
21:28 where we explore computer architecture and how transistors work,
21:32 and we can’t do it without your help.
21:36 The best way you can help is by taking a few seconds to scroll down,
21:42 write a comment below, like this video,
21:44 subscribe if you haven’t already and then share this video
21:48 on social media or send it to a friend or colleague.
21:52 Truly, just a few seconds of your time helps far more than you think.
21:59 Additionally, we have a Patreon page where we’ll be releasing behind
22:04 the scenes footage of our work and updates for upcoming videos.
22:08 If you find what we do useful, we would appreciate any support.
22:14 Thank you.
22:15 So then, what are the additional steps in manufacturing a microchip?
22:20 Before chip manufacturing at the fab, we first have to manufacture the silicon
22:26 wafers by refining quartzite into pure silicon,
22:29 and then growing a monocrystalline ingot and cutting it into wafers.
22:34 For reference, these 300-millimeter wafers are
22:37 around three-quarters of a millimeter thick,
22:41 they have a barcode on the side and a small
22:43 notch in them to indicate the direction of the crystal lattice.
22:47 Furthermore, these wafers are incredibly delicate,
22:50 and shatter into hundreds of shards when broken.
22:54 A single wafer costs around a hundred dollars,
22:57 but after being populated with CPUs it’s
23:01 worth closer to a hundred thousand dollars,
23:04 making it quite literally ten times more valuable than its weight in gold.
23:10 Moving onto the steps after chip manufacturing.
23:13 The completed wafer is sent to a separate building where each
23:17 of the CPUs undergoes rigorous testing to figure out if it works as intended.
23:22 If a CPU works, that’s great.
23:25 But frequently a particle or photomask defect
23:28 has damaged a section of the integrated circuit,
23:31 rendering that section defective.
23:33 These semi-functional circuits are then categorized,
23:36 or binned, based on what still works.
23:40 These Intel Thirteenth Gen processors are sold as an i9, i7, i5, or i3,
23:47 depending on how many cores are functional with different product
23:52 lines of CPUs whose on-board integrated graphics sections are defective.
23:57 These wafers are transported to another building where
24:00 the chips are cut out using a laser, flipped over,
24:04 and placed on an interposer which distributes the connection points to a printed
24:10 circuit board while a protective heat conductive
24:12 cover is placed on the back side.
24:15 The printed circuit board holds the landing grid array
24:19 that interfaces with the motherboard as well as various electrical components.
24:23 Next an integrated heat spreader is mounted on top,
24:28 and the entire assembly is tested one last time before being packaged for sale.
24:35 Finally, the CPU is now ready to be mounted
24:38 onto the motherboard and installed into your desktop computer.
24:42 It’s important to understand that chip manufacturing requires an incredible
24:47 amount of science and engineering and there’s a free
24:51 and easy way to learn the basic principles inside each
24:55 of these complex tools and that’s with this video’s sponsor, Brilliant.org!
25:01 Brilliant reimagines how courses are taught.
25:04 Instead of boring hour-long lectures or textbooks that put you to sleep,
25:11 Brilliant uses fun and interactive modules inside thousands of lessons
25:16 from basics to advanced topics– and new lessons are added every month.
25:21 Whatever your skill level, Brilliant customizes its content to fit your needs
25:27 and allows you to learn at your own pace.
25:30 We use Brilliant daily.
25:32 We’re working on videos on how AI and Chat GPT Works,
25:37 and so each of our animators is progressing
25:41 through their lessons on How Large Language Models work.
25:45 Because you’re watching this video,
25:47 you probably enjoy learning about how technology works,
25:51 and fortunately for you, Brilliant just added a course on this very topic.
25:56 In it they have lessons such as How GPS Works, How Computer Memory Works,
26:04 and how Recommendation Algorithms such as those used by YouTube work.
26:09 If you’re looking to advance your career,
26:12 Brilliant is the go-to resource for leveling up your skills
26:16 and staying up-to-date on the latest concepts behind world-changing technology.
26:21 For the viewers of this channel, Brilliant is offering a free 30-day trial
26:27 with access to all their thousands of lessons.
26:31 Additionally, Brilliant is offering 20% off an annual subscription.
26:35 Just go to brilliant.org/brancheducation.
26:38 The link is in the description below.
26:44 Microchip Fabrication is a massive topic, and thus,
26:48 we have two more equally complex videos that we’re working on.
26:53 The first will be an in-depth 3D animated
26:56 factory tour and the second will explore transistor physics,
27:01 FinFets, and the next generation of transistors.
27:04 We’re also working on a series of videos on GPUs and a separate one
27:10 on CPU architecture so make sure to subscribe
27:14 so you don’t miss any of our videos.
27:17 We’re thankful to all our Patreon
27:19 and YouTube Membership Sponsors for supporting our work.
27:23 If you want to financially support our work,
27:26 you can find the links in the description below.
27:30 This is Branch Education, and we create 3D animations that dive deeply
27:35 into the technology that drives our modern world.
27:38 Watch another Branch video by clicking one
27:41 of these cards or click here to subscribe.
27:45 Thanks for watching to the end!