How are Microchips Made? 🖥️🛠️ CPU Manufacturing Process Steps

How are Microchips Made? 🖥️🛠️ CPU Manufacturing Process Steps

Branch Education

0:00 Inside this smartphone are 62 microchips

0:03 containing a total of 90 billion transistors.

0:07 These microchips are incredibly powerful and the cornerstone of all technology,

0:12 but how are billions of nanoscopic transistors manufactured

0:16 into a microchip the size of a tiny ant?

0:20 Well, all these microchips were manufactured

0:23 in a semiconductor fabrication plant like this one.

0:27 Inside it is a clean room which spans the area

0:31 of 8 football fields and is filled with hundreds of machines ranging

0:35 in size from that of a van to that of a city

0:39 bus and costing anywhere between a few million and 170 million dollars.

0:46 Within this microchip factory,

0:48 silicon wafers travel from machine to machine and undergo

0:53 around a thousand processes over a 3-month period.

0:57 And, by the end of production, each silicon wafer will be covered in hundreds

1:03 of CPU chips each containing 26 billion transistors.

1:06 When we zoom in we can see the nanoscopic transistors

1:11 at the bottom and over a dozen layers of wires above.

1:16 This integrated circuit is then cut out from the wafer, tested,

1:20 and packaged so that it can be installed into your desktop computer.

1:25 In this video we’re going to explore the entire microchip

1:29 manufacturing process and show you how billions of nanoscopic transistors

1:34 and an impossibly complex 3D maze of wires are manufactured

1:39 in one of the world’s most technologically advanced microchip factories.

1:45 It’s an incredibly complicated process, so stick around and let’s jump right in!

1:55 A portion of this video is sponsored by Brilliant.org.

2:03 There are two sides to understanding how microchip manufacturing works.

2:08 The first is the sequence of steps and processes needed

2:12 to build the nanoscopic transistors and the labyrinth of wires.

2:17 Whereas the second is how the semiconductor fab

2:20 and multimillion dollar equipment on the cleanroom floor work,

2:25 and we’ll be flipping between these two sides to get a complete picture.

2:31 Let’s start by opening up this desktop computer,

2:33 focusing on the CPU and taking a look at what’s inside.

2:38 Here we have an integrated circuit, or die, which we’ll refer to as a chip.

2:44 This chip has 24 cores, a memory controller,

2:48 a graphics processor, and many other sections.

2:51 Within one of the cores, we can see its block diagram and the various elements.

2:56 Zooming in on this multiply block, we find a layout of 44 thousand transistors

3:03 that physically execute 32-bit multiplication and constitute just

3:07 point zero zero zero one seven percent

3:11 of the overall 26 billion transistors in the CPU.

3:16 Zooming in even further, we see layers of metal wires, or interconnects,

3:22 and at the very bottom are the transistors that form the basic logic gates.

3:27 Note that these layers of metal interconnects aren’t floating, but rather,

3:32 the empty space that you see is filled with insulating materials,

3:37 thus providing structure, and preventing the metal wire layers from touching.

3:42 Furthermore, here we’re only showing the transistors at the bottom and five

3:47 layers of metal interconnects with vias traveling vertically between the layers.

3:52 In actuality there are a total of 17 metal layers of wires in the CPU,

3:58 and each successive set of levels uses larger and larger interconnects.

4:03 At the bottom are local interconnects that move

4:06 data around this 32 bit multiply circuit.

4:09 In the middle are intermediate interconnects that move data around the core,

4:14 and at the top are global interconnects that move data around the entire CPU.

4:20 You might be wondering how small are these transistors?

4:24 Zooming in again and past the interconnect layers we find FinFets,

4:30 which are transistors whose channel dimensions are 36 by 6

4:35 by 52 nanometers with a transistor to transistor pitch of 57 nanometers.

4:42 Clearly the transistors are incredibly small.

4:45 Here’s a mitochondria, a dust particle, and a human hair for size comparisons.

4:52 Now that you have a sense of what

4:55 the transistors and labyrinth of metal interconnects look like,

4:59 let’s explore how they’re manufactured.

5:01 We’ll begin with an analogy.

5:04 Imagine baking a cake that’s 80 layers tall,

5:08 with each layer cut to a unique shape.

5:11 To make this cake there are 940 steps in the recipe,

5:16 which takes 3 months to complete and includes hundreds of exotic ingredients.

5:21 And, if any measurement, baking time,

5:24 or temperature is more than one percent off, then the cake is entirely ruined.

5:30 That’s kind of what it’s like to make a microchip,

5:34 but microchips are even more complicated.

5:37 Let’s look at a single layer of this integrated circuit

5:41 and run through a simplified set of steps used to build it.

5:46 To start, a layer of insulating silicon dioxide is deposited on top of the wafer

5:52 and then a layer of light sensitive photoresist is spread across the top.

5:58 Next, using UV Light and a stencil, a pattern is applied to the photoresist.

6:05 Solvents then are used to remove the areas hit by the UV light,

6:10 thus creating a patterned mask layer.

6:13 Using the mask, the revealed silicon dioxide

6:17 is etched away down to the previous layer.

6:21 Next the mask layer is removed,

6:23 and a layer of copper is added to cover the wafer

6:28 and fill in the areas that were just etched away.

6:32 Finally, the surface is ground down and leveled

6:35 off to reveal the copper and insulator patterns.

6:39 And thus, a single layer is completed.

6:43 In order to build the next layer, which is a vertical set of metal vias,

6:48 we repeat the same set of steps, but use a different pattern for the photomask.

6:54 Since these layers are all built using the same set of steps

6:59 it’s more effective to visualize the steps as a circle like a clock.

7:04 To build all the 80 layers of the die,

7:08 this sequence is repeated over and over, resulting in 940 steps.

7:13 One important note is that the FinFet transistors

7:18 at the bottom are even more complicated than the metal wires,

7:23 and thus additional steps are needed to fabricate them.

7:26 Furthermore, cleaning the wafer to wash away dust

7:30 particles that may have landed on the wafer,

7:33 as well as inspecting the wafer to make sure everything is being built properly,

7:38 happens frequently and these steps need to be added to the circle.

7:43 A different tool is used to complete each of these process steps.

7:48 Now that we have an understanding of the steps,

7:52 let’s take a look at this semiconductor fabrication plant.

7:56 This CPU is manufactured on a 300-millimeter

7:59 silicon wafer which can fit 230 CPU chips.

8:04 In contrast DRAM chips are considerably smaller and thus

8:09 952 of them can fit on a wafer.

8:13 These silicon wafers are carried in stacks of 25 using

8:18 a container called a front opening universal pod, or foup.

8:23 This sealed plastic wafer carrier is

8:26 transported around the cleanroom floor using

8:29 an overhead transport system which lowers the foup onto the tool’s landing pad.

8:35 Inside the tool, robotic arms transport the wafer through vacuum

8:40 load locks and to different process chambers where materials are added,

8:45 removed, or processed in ways that we’ll explore later.

8:48 The wafers are then returned to the foup,

8:52 resealed inside, lifted up to the overhead transport system,

8:56 and carried to and dropped onto the next tool,

8:59 where the next step in the process is completed.

9:03 To build the entire chip composed of 80

9:06 different layers it takes 3 months of traveling

9:09 from tool to tool where at each stop one of the 940 process steps is completed.

9:15 In order to increase the microchip mass production

9:19 capabilities of a semiconductor fabrication plant or fab,

9:22 typically there are dozens of the same semiconductor

9:26 tools organized in rows that perform the same process.

9:31 On the cleanroom floor there are a total of 435 semiconductor tools resulting

9:37 in the fab’s production capacity of 50,000 wafers or 11.5 million CPUs a month.

9:45 These tools have rather complicated names,

9:49 so we’ll start by categorizing them according to their functionality.

9:53 There are 6 groups: making the mask layer, adding material, removing material,

10:00 modifying the material, cleaning the wafer, and finally inspecting the wafer.

10:05 We’ve color coded the different functional groups to the various

10:10 tools and process steps to help you not get lost.

10:15 Let’s next look at each of these semiconductor tools

10:18 and see how they process the wafer in various ways.

10:22 We’ll start with the ones that are used to make

10:25 the mask layer or the nanoscopic stencil on the wafer.

10:29 These tools include the photoresist spin coater,

10:33 photolithography tool, developer and photoresist stripper.

10:37 First the photoresist spin coater applies a light-sensitive layer

10:42 to the surface of the wafer and sends it

10:45 through a soft bake where the wafer is heated

10:47 in order to evaporate the solvent from the photoresist.

10:51 Next the wafer goes to the lithography

10:54 tool which shines UV light through a stencil,

10:58 which is technically called a photomask.

11:00 The light passes through the stencil and is then demagnified

11:05 or shrunk down to produce a nanoscopic pattern on the wafer.

11:09 Wherever the light from the stencil touches the wafer,

11:12 the photoresist is weakened.

11:14 The wafer then goes to the developer

11:17 and the weakened photoresist is washed away,

11:20 leaving only the patterned nanoscopic stencil on the wafer.

11:23 The wafer is then sent through a hard bake to harden the remaining photoresist.

11:29 Next the wafer travels to other tools to undergo processing,

11:34 and once these processes are completed the wafer goes to a photoresist

11:40 stripper which uses solvents to dissolve and remove the photoresist mask layer.

11:45 And that’s how a mask layer is formed and then removed.

11:50 The photolithography tool is one of the most important,

11:53 so let’s take a look at it.

11:56 Inside is a UV light source, a set of lenses to focus the light,

12:01 a photomask which contains the stencil,

12:04 or design of the layer to be patterned, and a wafer carrier.

12:09 The photomask is 6 by 6 inches, and, based on the dimensions of the CPU,

12:16 can fit 2 copies of a single layer of the CPU design.

12:20 The purpose of using a photomask with these crazy optics

12:24 is because it’s a reliable way to copy and paste

12:28 a design for billions of nanoscopic transistors and wires onto

12:34 230 identical CPUs on a single wafer in a few minutes.

12:40 After the light passes through the photomask,

12:43 the UV light goes to more lenses in order to shrink down the pattern

12:48 by a factor of 4 and print a single layer of the design onto the photoresist.

12:54 The wafer carrier steps from position to position,

12:58 printing the photomask image at each stop, until all 230 chips are patterned.

13:05 Let’s clarify one detail.

13:07 In our previous examples, we talked a lot about this CPU having 80 layers.

13:13 Specifically, what we were referring to is the number of photomasks and mask

13:18 layers used to create all the different layers of patterns on the wafer.

13:23 Therefore, one complete CPU chip uses 80 different photomasks,

13:29 each costing 300,000 dollars.

13:31 With only one mask layer being patterned at a time,

13:36 this CPU chip will undergo 80 separate visits to the lithography tool.

13:42 We could spend another hour talking about photolithography

13:45 but let’s move onto the next category of tools.

13:49 Deposition tools are used to add or deposit material onto the wafer.

13:54 A lot of times we use the mask layer from the photolithography

13:59 step to add materials to the areas uncovered by the mask layer,

14:03 kind of like spray painting through a stencil.

14:06 Due to the wide range of elements and compounds used to create the layers,

14:12 deposition tools have a wide range of variations

14:15 with complicated names and acronyms for each variant.

14:19 But essentially there are 3 key groups of materials

14:23 that are added or deposited onto the wafer: metals such as copper or tantalum,

14:30 insulators which are typically called oxides, and crystalline layers of silicon.

14:35 Each group of different materials uses different

14:38 physics and chemistry principles to deposit the material

14:41 on the wafer and therefore has a different

14:44 technical name for the tool that deposits the material.

14:48 Deposition tools typically have a central wafer handling chamber,

14:51 with the various chambers attached to the edges,

14:55 each one dedicated to adding just a single element or compound.

15:00 The next category of machines do the opposite, which is to remove material.

15:06 There are 2 key methods.

15:08 The first is etching.

15:10 Etchers use either corrosive chemicals or high energy plasmas to react

15:15 with and remove materials from the surface of the wafer.

15:19 They are typically used with the mask layer stencil

15:21 in order to remove the material exposed by the mask,

15:25 thus creating a hole that can be later filled by a deposition tool.

15:29 The second method to remove material is CMP,

15:34 which is chemical mechanical planarization.

15:37 CMP applies slurry and uses abrasive pads to grind

15:40 and polish away the top surface of the wafer, making it perfectly flat.

15:45 CMP levels off the top layers of the wafer

15:49 and is typically used as the last step

15:52 in a cycle of processes in order to prepare

15:55 the wafer for another layer to be added.

15:57 The fourth category are tools that modify

16:00 the silicon and are called ion implanters.

16:04 These tools use the photomask stencil

16:06 to bombard the unmasked regions with phosphor, boron,

16:11 or other elements in order to make the P

16:15 and the N regions required to form the transistors themselves.

16:19 Therefore, ion implanters are only used in the front end of line.

16:23 You might think that this is adding material.

16:26 However, ion implanters only add around one atom

16:30 of phosphor or boron for every 10,000 atoms of silicon.

16:34 Additionally, while other machines spray paint a layer on top of the wafer,

16:40 ion implanters hurl atoms deep into the silicon lattice,

16:43 kind of like a cannon launching a baseball 6 feet into a concrete wall.

16:49 This process typically damages the silicon lattice,

16:52 which is why the following step is to repair the silicon

16:56 by heating the wafer using a separate tool called an annealer.

17:00 The fifth category of tools are used to clean

17:04 and remove any contaminants or particles from the wafer.

17:07 These wafer washers use ultra-pure water to clean the wafer

17:11 and then dry it with nitrogen or hot isopropyl alcohol.

17:15 Cleaning the wafer happens rather frequently in order to remove

17:19 any stray particles that may have fallen onto the wafer.

17:24 And finally, sixth are tools that inspect the transistors

17:28 and metal layers for defects and are called metrology tools.

17:32 A common metrology tool uses a scanning electron microscope

17:36 with nanometer-level resolution to take pictures of the top surface

17:41 of the wafer and determine if there are defects

17:44 such as improperly patterned layers or particles on the surface.

17:48 When fabricating an integrated circuit that takes 3 months to complete,

17:52 it’s important to repeatedly monitor the progress and make sure

17:56 that each of the processes is being executed with nanometer-level precision.

18:02 Now that we’ve covered each of the categories,

18:06 here are the color coded process steps along

18:08 with the layout of the tools in the semiconductor fabrication plant.

18:12 Let’s run through the complete set of steps

18:15 used to manufacture a single metal interconnect layer.

18:19 First a layer of insulating silicon dioxide is deposited onto the wafer.

18:26 Next photoresist is spread across the surface and the wafer

18:30 is sent through a soft bake to remove the solvent.

18:34 The wafer then travels to the photolithography tool

18:37 where the design from the photomask is transferred

18:40 to each of the chips on the wafer

18:42 by weakening the areas of photoresist hit by the light.

18:45 The wafer next goes to the developer to wash away the sections that were hit

18:50 by the light from the lithography tool and then

18:53 through a hard bake to harden the remaining photoresist.

18:56 With the mask layer built, the wafer goes to an etching tool,

19:01 where a plasma etcher removes a vertical column through the exposed

19:06 silicon dioxide until it reaches the previous layer’s metal vias.

19:10 Next the wafer is sent to a photoresist

19:13 stripper where the mask layer is removed.

19:16 The wafer then travels to a physical vapor deposition tool where a sequence

19:22 of metals fills in the exposed pattern and coats the wafer in metal.

19:27 Finally the wafer is sent to a chemical mechanical planarization

19:31 tool where the metal is ground down so that all

19:35 that remains is a flat layer of insulating silicon dioxide

19:40 and conductive copper interconnects that match the pattern from the photomask.

19:45 A single metal layer is now completed,

19:48 and the wafer is ready for the next cycle to begin

19:52 where insulating silicon dioxide and the vias will be added.

19:57 Note that cleaning and wafer metrology or inspection

20:00 steps occur in between many of these other steps.

20:04 Furthermore, the process steps to make the transistors

20:08 are less straightforward and utilize the ion implanter,

20:11 and thus we’ll cover them in a separate video on transistor physics and design.

20:16 These steps are for building the integrated circuit on the wafer, however,

20:21 there are additional steps in manufacturing a microchip

20:24 which we’ll explore in a little bit.

20:26 But before we get there, one important thing to note is

20:31 that the semiconductor industry is incredibly secretive regarding

20:34 the exact tool layout and the process

20:37 steps and recipes used to make the transistors.

20:41 We wanted to make the best video on how microchips are made and it took us 180

20:47 hours of scouring the internet and textbooks for information

20:52 and reference images and, using what we found,

20:56 we spent 205 hours modeling each of these tools,

21:01 the many layers of the integrated circuit, and the semiconductor fab.

21:06 Furthermore, writing the script took about 100 hours,

21:11 and then animating all these visuals took more than 825 hours.

21:17 As a result, this video took over 1300 hours to make,

21:23 and it’s entirely free to watch.

21:25 We want to make more videos like this one

21:28 where we explore computer architecture and how transistors work,

21:32 and we can’t do it without your help.

21:36 The best way you can help is by taking a few seconds to scroll down,

21:42 write a comment below, like this video,

21:44 subscribe if you haven’t already and then share this video

21:48 on social media or send it to a friend or colleague.

21:52 Truly, just a few seconds of your time helps far more than you think.

21:59 Additionally, we have a Patreon page where we’ll be releasing behind

22:04 the scenes footage of our work and updates for upcoming videos.

22:08 If you find what we do useful, we would appreciate any support.

22:14 Thank you.

22:15 So then, what are the additional steps in manufacturing a microchip?

22:20 Before chip manufacturing at the fab, we first have to manufacture the silicon

22:26 wafers by refining quartzite into pure silicon,

22:29 and then growing a monocrystalline ingot and cutting it into wafers.

22:34 For reference, these 300-millimeter wafers are

22:37 around three-quarters of a millimeter thick,

22:41 they have a barcode on the side and a small

22:43 notch in them to indicate the direction of the crystal lattice.

22:47 Furthermore, these wafers are incredibly delicate,

22:50 and shatter into hundreds of shards when broken.

22:54 A single wafer costs around a hundred dollars,

22:57 but after being populated with CPUs it’s

23:01 worth closer to a hundred thousand dollars,

23:04 making it quite literally ten times more valuable than its weight in gold.

23:10 Moving onto the steps after chip manufacturing.

23:13 The completed wafer is sent to a separate building where each

23:17 of the CPUs undergoes rigorous testing to figure out if it works as intended.

23:22 If a CPU works, that’s great.

23:25 But frequently a particle or photomask defect

23:28 has damaged a section of the integrated circuit,

23:31 rendering that section defective.

23:33 These semi-functional circuits are then categorized,

23:36 or binned, based on what still works.

23:40 These Intel Thirteenth Gen processors are sold as an i9, i7, i5, or i3,

23:47 depending on how many cores are functional with different product

23:52 lines of CPUs whose on-board integrated graphics sections are defective.

23:57 These wafers are transported to another building where

24:00 the chips are cut out using a laser, flipped over,

24:04 and placed on an interposer which distributes the connection points to a printed

24:10 circuit board while a protective heat conductive

24:12 cover is placed on the back side.

24:15 The printed circuit board holds the landing grid array

24:19 that interfaces with the motherboard as well as various electrical components.

24:23 Next an integrated heat spreader is mounted on top,

24:28 and the entire assembly is tested one last time before being packaged for sale.

24:35 Finally, the CPU is now ready to be mounted

24:38 onto the motherboard and installed into your desktop computer.

24:42 It’s important to understand that chip manufacturing requires an incredible

24:47 amount of science and engineering and there’s a free

24:51 and easy way to learn the basic principles inside each

24:55 of these complex tools and that’s with this video’s sponsor, Brilliant.org!

25:01 Brilliant reimagines how courses are taught.

25:04 Instead of boring hour-long lectures or textbooks that put you to sleep,

25:11 Brilliant uses fun and interactive modules inside thousands of lessons

25:16 from basics to advanced topics– and new lessons are added every month.

25:21 Whatever your skill level, Brilliant customizes its content to fit your needs

25:27 and allows you to learn at your own pace.

25:30 We use Brilliant daily.

25:32 We’re working on videos on how AI and Chat GPT Works,

25:37 and so each of our animators is progressing

25:41 through their lessons on How Large Language Models work.

25:45 Because you’re watching this video,

25:47 you probably enjoy learning about how technology works,

25:51 and fortunately for you, Brilliant just added a course on this very topic.

25:56 In it they have lessons such as How GPS Works, How Computer Memory Works,

26:04 and how Recommendation Algorithms such as those used by YouTube work.

26:09 If you’re looking to advance your career,

26:12 Brilliant is the go-to resource for leveling up your skills

26:16 and staying up-to-date on the latest concepts behind world-changing technology.

26:21 For the viewers of this channel, Brilliant is offering a free 30-day trial

26:27 with access to all their thousands of lessons.

26:31 Additionally, Brilliant is offering 20% off an annual subscription.

26:35 Just go to brilliant.org/brancheducation.

26:38 The link is in the description below.

26:44 Microchip Fabrication is a massive topic, and thus,

26:48 we have two more equally complex videos that we’re working on.

26:53 The first will be an in-depth 3D animated

26:56 factory tour and the second will explore transistor physics,

27:01 FinFets, and the next generation of transistors.

27:04 We’re also working on a series of videos on GPUs and a separate one

27:10 on CPU architecture so make sure to subscribe

27:14 so you don’t miss any of our videos.

27:17 We’re thankful to all our Patreon

27:19 and YouTube Membership Sponsors for supporting our work.

27:23 If you want to financially support our work,

27:26 you can find the links in the description below.

27:30 This is Branch Education, and we create 3D animations that dive deeply

27:35 into the technology that drives our modern world.

27:38 Watch another Branch video by clicking one

27:41 of these cards or click here to subscribe.

27:45 Thanks for watching to the end!

Study with Looplines Download Captions Watch on YouTube